Unreasonable unloading time parameters

由于自動上料攪拌機無法在料倉中安裝水平儀，因此該行業基本上具有時間控制功能。如何設置時間參數，加載和卸載時間設置實際上非常簡單。使用時，請設置較短的時間，然后根據每個抽吸位置緩慢添加。當物料水平達到吸入口時間時，可以減去一秒鐘。排出時間是為了確保再次排出物料。這具有兩個優點：首先，材料水平太高，并且對濾芯的損壞特別大。因此，我們的一些客戶可以使用過濾器兩年半。

Since the automatic feeding mixer can not be installed in the silo level, so the industry basically has the function of time control. How to set the time parameters, load and unload time settings are actually very simple. When using, please set a short time, and then add slowly according to each suction position. When the material level reaches the suction time, one second can be subtracted. The discharge time is to ensure that the material is discharged again. This has two advantages: first, the material level is too high, and the damage to the filter element is particularly large. As a result, some of our customers can use the filter for two and a half years.

其次，每次清潔材料時，截止閥都不會在關閉時關閉。頻繁操作的密封閥將不會切換五到六次，這是特別危險的。

Second, each time the material is cleaned, the stop valve will not close when it is closed. Frequently operated seal valves will not switch five to six times, which is particularly dangerous.

我們的許多項目都使用手動槍來撿拾材料。為了便于將物料槍直接插入物料管或噸袋中，物料槍的吸入口被緊密的物料壓縮，強大的負壓將整個物料拉開。裝載機的破壞力非常強，很容易堵塞管道。正確的方法是，物料在吸入口和空氣之間形成一定的氣液混合比，并在氣流的推動下均勻地流入進料器。如果物料積壓太長，則可能非常困難。此時，在噴槍上需要一個振蕩器來破壞冷凝的材料。

Many of our projects use hand guns to pick up materials. In order to insert the material gun directly into the material pipe or the ton bag, the suction port of the material gun is compressed by the tight material, and the whole material is pulled apart by the strong negative pressure. The destructive power of the loader is very strong, and it is easy to block the pipeline. The correct way is that the material forms a certain gas-liquid mixing ratio between the suction port and the air, and flows into the feeder evenly under the push of the air flow. If the material backlog is too long, it can be very difficult. At this time, an oscillator is needed on the spray gun to destroy the condensed material.

在自動上料攪拌機的實際操作中，不可避免地會發生某些故障。阻隔材料更嚴重。因此，希望在理解了上述自動上料攪拌機的避免方法后，能夠正確，合理地操作設備。

In the actual operation of the automatic feeding mixer, some failures will inevitably occur. The barrier material is more serious. Therefore, I hope that after understanding the above methods of automatic feeding mixer, I can operate the equipment correctly and reasonably.

不要超載。始終注意工作條件。環境溫度高于25攝氏度，裝載，運輸和卸載時間不應超過60分鐘。環境溫度低于25攝氏度，上述時間不應超過90分鐘。液壓系統的壓力符合使用說明書，不能隨意調節。液壓油的質量和數量必須符合原始要求。

Don't overload. Always pay attention to working conditions. When the ambient temperature is higher than 25 ℃, the loading, transportation and unloading time shall not exceed 60 minutes. If the ambient temperature is lower than 25 ℃, the above time shall not exceed 90 minutes. The pressure of the hydraulic system is in accordance with the operation manual and cannot be adjusted at will. The quality and quantity of hydraulic oil must meet the original requirements.

在施工現場卸貨后自動使用連接到攪拌機的軟管清潔漏斗，排水漏斗，排水斜槽等，以清除附著在車身上的污泥和混凝土。 在返回攪拌站的途中，將150-200升水倒入攪拌罐中，以清除殘留在攪拌罐壁和葉片上的所有混凝土。

After unloading at the construction site, the hose connected to the mixer is automatically used to clean the funnel, drainage funnel, drainage chute, etc. to remove the sludge and concrete attached to the vehicle body. On the way back to the mixing plant, pour 150-200 liters of water into the mixing tank to remove all concrete remaining on the tank walls and blades.