1： When operating the automatic feeding mixer, keep the heel close to the floor of the cab, keep the pedal parallel to the accelerator pedal, and press the accelerator pedal slowly.

2：自動進紙混合器運行時，節氣門應始終保持穩定。在正常工況下，節氣門開度約為70％。

2: The throttle should always be stable when the automatic feeder mixer is running. Under normal operating conditions, the throttle opening is about 70%.

3：操作自動上料混凝土攪拌車時，腳踏板應與制動踏板分開，并平放在駕駛室地板上。自動裝載攪拌機通常在不平坦的建筑工地上工作。如果您的腳一直踩在制動踏板上，您的身體會上下移動，駕駛員會無意間踩到制動踏板。通常情況下，有必要通過控制節氣門的減速度來控制發動機和變速齒輪的狀態。這不僅避免了頻繁的制動和制動系統的過熱，而且還提高了自動供料攪拌機的便利性。

3: When operating the automatic charging mixer, the pedal should be separated from the brake pedal and placed flat on the cab floor. Automatic loading mixer usually works on uneven construction site. If you step on the brake pedal all the time, your body will move up and down, and the driver will step on the brake pedal unintentionally. Usually, it is necessary to control the state of the engine and gear by controlling the deceleration of the throttle valve. This not only avoids frequent braking and overheating of the braking system, but also improves the convenience of the automatic feeding mixer.

4：在操作自動供料攪拌機時，尤其是在操作鏟斗時，必須在節流閥穩定的同時定期向上提起提升桿和鏟斗操作桿，以向鏟斗中填充物料。

4: When operating the automatic feeding mixer, especially when operating the bucket, the lifting rod and bucket operating lever must be lifted up regularly to fill the bucket while the throttle valve is stable.

5：禁止輪胎側滑。當混凝土自動上料混凝土攪拌車運行時，遇到阻力時，加速器突然踩踏，輪胎經常打滑。此現象通常是由不當的駕駛員操作引起的。

5: Do not allow tire sideslip. When the concrete automatic loading mixer runs, when encountering resistance, the accelerator suddenly steps on, and the tire often slips. This phenomenon is usually caused by improper driver operation.

這將增加油耗并損壞輪胎。第二是防止后輪傾斜。由于自動上料混凝土攪拌車的鉆孔能力強，駕駛員通常會鏟掉堅硬的原土和落基山脈。如果操作不正確，則將兩個后輪簡單地抬離地面。提升操作的地面慣性導致鏟斗葉片破裂和變形。如果后輪高，鋼板以及前框架和后框架等焊接部件都會斷裂。第三是禁止上山。剃刮普通物料時，自動飼料攪拌機以2檔運行，并且禁止慣性沖擊2檔以上的齒輪組。

This will increase fuel consumption and damage the tires. The second is to prevent the rear wheels from tilting. Due to the strong drilling capacity of the automatic charging mixer, the driver usually shovel away the hard original soil and Rockies. If the operation is not correct, simply lift both rear wheels off the ground. The ground inertia of the lifting operation causes the bucket blades to crack and deform. If the rear wheel is high, the steel plate and welded parts such as the front and rear frames will break. Third, it is forbidden to go up the mountain. When the mixer is above 2 gears, it is forbidden to impact the normal gear when shaving the feed automatically.